Other
Part of: 732020 — Helical springs:
N348645 · 2025-05-23 — The tariff classification of engine valve springs from Mexico
Technical information was submitted with your request. The items under consideration are described as engine valve springs specifically designed for use in internal automotive combustion engines. During engine operation, the engine valve springs function to keep the engine’s valves closed when they are not opened by the camshaft. You assert that this function is integral to maintain proper valve timing and combustion efficiency. In addition, the subject valve springs and raw materials are highly engineered, tested, and certified to operate under extreme conditions such as heat, pressure, and…
N319637 · 2021-06-09 — The tariff classification of a spring cartridge assembly from Italy
Product descriptions, photographs and technical drawings were submitted for our review. The subject product is identified as Aegis Item Part Number RE-201/SR-Spring (Manufacturer Part Number – SR201) and is used in a Rack and Pinion Style Spring Return Pneumatic Actuator. The subject helical spring is made of steel and is assembled with a stainless steel bolt and nut that pre-compress the spring using two nylon spring guides. The spring wire diameter is approximately 6.60 mm. You stated in your letter that “These springs are installed behind the pistons in the Rack and Pinion Actuators. As…
K88036 · 2004-08-10 — The tariff classification of helical steel springs from Japan.
We are returning the samples as you have requested. The items are 3 different sizes of steel springs that are designed for use in plastic injection molds. The steel springs are described as part numbers SWU14.5-40, 77158-04010, and GF181-01450. The applicable subheading for part number SWU14.5-40 will be 7320.20.5020, Harmonized Tariff Schedule of the United States (HTS), which provides for springs and leaves for springs, of iron or steel, helical springs, other, helical springs, of wire having a cross-sectional dimension of less than 5.1 millimeters, other. The rate of duty will be 3.9% ad…
962480 · 1999-09-07 — Compressor Mounting Kit
Your letters to the Customs National Commodity Specialist Division, New York, dated December 7 and 16, 1998, concerning the classification under the Harmonized Tariff Schedule of the United States (HTSUS), of a compressor mounting kit has been referred to this office for reply. A sample kit and mounting instructions were submitted. We regret the delay in responding. FACTS: The kit consists of four(4) base metal isolation springs, two (2) steel spring retainers, four (4) threaded steel studs, eight (8) steel flange nuts, four (4) rubber snubbers, four (4) steel snubber cups and four (4)…
956900 · 1995-07-10 — Protest 4115-94-100005; Automotive Components; Explanatory Notes 48.23, 84.21, 85.01, and 85.12; Chapter 39, Note 2(p); Chapter 90, Note 6; Section XVI, Notes 1(a) and 2; Section XVII, Notes 2(a) and (f); HQs 951279, 951976, and 954581; Intercargo Insurance Co., f/k/a International Cargo & Surety Co. (Surety for M.Genauer) v. U.S.; 3923.90.00; 3926.90.90; 4823.90.85; 5911.90.00; 7318.15.20; 7318.21.00; 7318.22.00; 7320.90.10; 8301.60.00; 8414.90.90; 8421.99.00; 8501.1
The following is our decision regarding Protest 4115-94-100005 concerning your action in classifying and assessing duty on certain automotive components under the Harmonized Tariff Schedule of the United States (HTSUS). FACTS: The merchandise consists of various automotive components, listed as follows: plastic front nozzle assemblies (part no. 1223419-GB); plastic rear tank assemblies (part no. 2223908-A); plastic rear nozzles (part nos. 2225109-AB and 2226365-AB); level sensors/grommet assemblies (part no. 2222450-BB); rubber boots (part no. 2231395-04); rubber duckbills (part no.…
Not sure this code fits your product? HaiLang AI determines the US HTS code from a description in about a minute.
Classify a product