Parts of aircraft gas turbines
Part of: 84119990 — Other
N257526 · 2014-10-21 — The tariff classification of a wheel assembly from France
N257526 October 21, 2014 CLA-2-84:OT:RR:NC:N1:106 CATEGORY: Classification TARIFF NO.: 8411.99.9090 Timothy A. Perez, Import/Export Compliance Coordinator Turbomeca USA 2709 N. Forum Drive Grand Prairie, TX 75052-8927 RE: The tariff classification of a wheel assembly from France Dear Mr. Perez, In your letter dated September 03, 2014, you requested a tariff classification ruling and application of the Civil Aircraft Agreement. The item under consideration is a Wheel Assembly used on an aircraft gas turbine. The turbine wheel assembly consists of the disc, blades, blade locks, and blade…
965789 · 2002-10-10 — Protest 1801-01-100080; Compressor Blades
This is our decision on Protest 1801-01-100080, filed on behalf of Siemens Westinghouse Power Corp., against your classification, under the Harmonized Tariff Schedule of the United States (HTSUS), of compressor blades used in non-aircraft gas turbines. The entry was liquidated on October 19, 2001, and this protest timely filed on November 20, 2001. FACTS: The merchandise at issue is described by the importer/protestant as blades for use in the axial compressor casing section of a combustion gas turbine. The composition of the blades and their dimensions are not further described. Gas turbines…
f89859 · 2000-07-31 — The tariff classification of blades and damper seals for various gas turbine engines from Mexico
, you requested a tariff classification ruling. The merchandise in question is a variety of blades and damper seals for use in a variety of gas turbines. The blades are internal components of gas turbines used to direct airflow to the turbine section of the engine. All of the blade part numbers in your request will be used in turbofan gas turbines for use in commercial aircraft. The damper seals are internal components of gas turbines used to keep the blades from vibrating. Some of these seals will be used in turbofan aircraft turbines, while the balance will be used either in commercial…
D87262 · 1999-01-27 — The tariff classification of a power section assembly from Canada.
You submitted descriptive literature with your request. The power section assembly is a component of the Pratt & Whitney PT6T helicopter turboshaft engine. The power section assembly is comprised of the following components: nuts, engine lifting bracket, rear fireseal installation, no. 3 and 4 bearing housing support assembly, power turbine rotor installation, and exhaust duct assembly. The applicable subheading for the power section assembly will be 8411.99.9090, Harmonized Tariff Schedule of the United States (HTS), which provides for parts of aircraft gas turbines. The rate of duty will be…
957578 · 1998-02-05 — PRD 4102 -94-100056; Mounting Base and Enclosure for Marine Gas Turbine; Fabricated Structural Components for Acoustic, Thermal and Vibration Protection; Parts of Gas Turbines; Articles of Iron or Steel, Subheading 7326.90.90, Bauerhin Technologies v. U.S.; Section XVI, Note 2; HQ 955501 Revoked; HQ 958295 Dear Port Director:
This is our decision on Protest 4102-94-100056, filed against your classification under the Harmonized Tariff Schedule of the United States (HTSUS), of a mounting base and enclosure for marine gas turbines. The entries were liquidated on June 24, 1994, and this protest timely filed on September 12, 1994. FACTS: Literature describes a gas turbine support structure or base (the Base) and an acoustic steel structure (the Enclosure), both fabricated essentially from carbon and stainless steel. These articles were assembled in the United States with a simple-cycle, two-shaft gas turbine into the…
Not sure this code fits your product? HaiLang AI determines the US HTS code from a description in about a minute.
Classify a product