Parts of gearing, gear boxes and other speed changers
N335422 · 2023-10-05 — The classification and country of origin of a pin and sleeve assembly
Descriptive literature was submitted. The pin and sleeve assembly is referred to as a matched set of tubes available in five different sizes. In use, a pin is inserted into a sleeve, and together, the pin and sleeve push against the track lugs located on the inside track of a machine, such as a shovel loader. Like a drive sprocket tooth, the pin and sleeve assembly transfers the rotational movement of the drive motor to the track of the machine. The pin and sleeve tubes will be imported together in the same quantities. In your letter, you suggest the pin and sleeve assembly is classified…
H310746 · 2021-02-03 — Application for Further Review of Protest No. 1703-20-103344; Classification of Automobile Bracket Lifts, Bracket Clamps, Bracket Cable Mountings, Backplate Assemblies, and Breather Assemblies.
1703-20-103344, timely filed by Sandler, Travis & Rosenberg, PA on behalf of protestant, Briggs & Stratton Corporation (“Briggs”). The protest contests the classification and liquidation by Customs and Border Protection of: 1) bracket lifts, bracket clamps, and bracket cable mountings under heading 7326 of the Harmonized Tariff Schedule of the United States (“HTSUS”), 2) backplate assemblies under heading 8483, HTSUS, and 3) breather assemblies under heading 8481, HTSUS. In reaching the below determination, we have considered information presented in the protest and AFR, supplemental…
957779 · 1995-07-13 — Protest 2904-95-100074; Cam gears; Hay baler, parts; Agricultural machinery
FACTS: The cam gear involved is a component part used in the knotter drive assembly of a hay baling machine. The unit is disc-shaped and contains two partial sets of gears as well as an actuating cam. When the knotter shaft is rotated, the first gear engages a separate pinion gear which moves as "bill hook" (a device for making a knot), while the second gear engages another pinion gear that advances the twine. The cam portion of this unit activates the knife arm, cutting the twine. The two entries covering this merchandise were liquidated on December 16, 1994, and January 20, 1995, under…
956900 · 1995-07-10 — Protest 4115-94-100005; Automotive Components; Explanatory Notes 48.23, 84.21, 85.01, and 85.12; Chapter 39, Note 2(p); Chapter 90, Note 6; Section XVI, Notes 1(a) and 2; Section XVII, Notes 2(a) and (f); HQs 951279, 951976, and 954581; Intercargo Insurance Co., f/k/a International Cargo & Surety Co. (Surety for M.Genauer) v. U.S.; 3923.90.00; 3926.90.90; 4823.90.85; 5911.90.00; 7318.15.20; 7318.21.00; 7318.22.00; 7320.90.10; 8301.60.00; 8414.90.90; 8421.99.00; 8501.1
The following is our decision regarding Protest 4115-94-100005 concerning your action in classifying and assessing duty on certain automotive components under the Harmonized Tariff Schedule of the United States (HTSUS). FACTS: The merchandise consists of various automotive components, listed as follows: plastic front nozzle assemblies (part no. 1223419-GB); plastic rear tank assemblies (part no. 2223908-A); plastic rear nozzles (part nos. 2225109-AB and 2226365-AB); level sensors/grommet assemblies (part no. 2222450-BB); rubber boots (part no. 2231395-04); rubber duckbills (part no.…
953825 · 1993-07-30 — Gears, Gearing, Pitman Arm, Connecting Linkage for Water Pumping Windmills; Cast Parts, Finished and Unfinished; Blanks, GRI 2(a) Dear Sir:
In a letter dated March 30, 1993, you inquire as to the tariff classification of certain cast parts from Mexico for a water pumping windmill. Photographs and cut-away drawings were submitted. FACTS: The parts in issue are the pinion gear (components A704 and B704), large gear both finished and "raw" or unfinished (designated A705 and B705), and the pitman arm both finished and "raw" or unfinished (designated A686 and B686). These are components of a windmill which will be connected after importation to a water pump which will serve as irrigation apparatus. The pinion gear consists of 2…
Not sure this code fits your product? HaiLang AI determines the US HTS code from a description in about a minute.
Classify a product