Other bars and rods, not further worked than cold-formed or cold-finished:
966169 · 2003-04-08 — Steel Bars with Chamfered Ends for use as Precision Linear Shafts;
We have considered this submission as a request for reconsideration of New York Ruling letter (NY) I85075, dated September 19, 2002. Your letter was forwarded to this office for reply. A sample was provided for our examination. After review of NY I85075, Customs and Border Protection (Customs) has determined that the classification of the chamfered precision linear shafts under subheadings 7215.50.00, 7222.20.00, 7228.50.50, HTSUS, is correct. FACTS: In NY I85075, in response to your classification request, certain nonalloy steel bars of circular cross section were classified under subheading…
E82976 · 1999-06-17 — The tariff classification and status under the North American Free Trade Agreement (NAFTA), of alloy steel and alloy tool steel plate from Canada; Article 509
, you requested a ruling on the status of alloy steel plate from Canada under the NAFTA. Hot-rolled flat-rolled alloy steel (AISI 4140 and AISI P20 having a carbon content of less than 0.3 percent) and alloy tool steel (AISI A2, AISI D2 and AISI P20 having a carbon content not less than 0.3 percent) plates ranging from 0.5 inch to 16 inches in thickness, from 40 inches to 80 inches in width and from 120 inches to 160 inches in length are produced in various European countries and imported into Canada. These hot-rolled alloy steel and alloy tool steel plates are classified under heading 7225,…
958623 · 1996-02-20 — PC 848161 Modified; Specialty Steel; Flat-Rolled Products, Specialty Steel Produced by Forging; Specialty Steel Produced by Flat-Rolling, Chapter 72, Note 1(k), HTSUS; Bars, Chapter 72, Note 1(m); Turning, Peeling, Mechanical Descaling, Cold-Forming, Cold-Finishing; HQ 955737, HQ 956468 Dear Mr. O'Donnell:
Preclassification (PC) decision 848161, issued to you on January 26, 1990, by the District (now Port) Director of Customs, Chicago, on behalf of Uddeholm Corporation, concerned the tariff classification of specialty steel identified as flat-rolled products, forged products, kleen ground flats/precision ground flats, precision machined drill rod and hollow bar. We have reconsidered the classification of the flat-rolled products and believe that it is incorrect. FACTS: The specialty steel described in PC 848161 under the heading Flat Rolled Products consists of steel meeting the definition of…
955737 · 1995-07-19 — PRD 3901-93-101490; Alloy Tool Steel Bars, Hot Rolled; Peeling, Turning, Machining; Cold Forming, Cold Finishing; Further Working; Mechanical Descaling; Subheading 7228.40.00; NY 847047 Distinguished Dear District Director:
This is our decision on Protest No. 3901-93-101490, filed against your classification of certain hot rolled alloy steel bars. The entries were liquidated on May 7, 1993, and this protest timely filed on August 5, 1993. The file contains submissions from counsel for protestant, dated October 21 and December 10, 1993, and August 2 and 28, 1994. In addition, counsel made an oral presentation at a meeting in our office on August 3, 1994. FACTS: The merchandise under protest is round, rectangular or block-shaped and flat bars of alloy tool steel, either press forged or roll forged from blooms or…
956468 · 1994-09-19 — Bar of Alloy and Nonalloy Steel; Hot-Rolled Bar Rough Turned to Remove Scale Then Annealed; Steel Bar Not Further Worked Than Hot-Rolled, Heading 7214; Other Bars and Rods, Heading 7215, Heading 7228; Cold Forming, Cold Finishing; HQ 079807, HQ 086464 Dear Mr. O'Donnell:
, you inquire as to the tariff classification of certain alloy and nonalloy steel bar from the UK. FACTS: Molten alloy and nonalloy steel is cast, presumably into billets, then hot-rolled in a primary rolling mill to sizes ranging from 3 to 12 inches in diameter. The bars are then rough turned to remove oxidation scale, a process which you state can result in the removal of between 6 and 10 percent, by weight, of the steel. You state this allows the bars to be delivered in imperial (inches) sizes rather that metric sizes. After rough turning the bars are annealed to bring them to their…
Not sure this code fits your product? HaiLang AI determines the US HTS code from a description in about a minute.
Classify a product