Having shanks or threads with a diameter of 6 mm or more: — Other: — Other: — Other
Part of: 73181520 — Bolts and bolts and their nuts or washers entered or exported in the same shipment
N350227 · 2025-07-15 — The classification, country of origin, and marking of a Tee Head Bolt Assembly and Mechanical Joint Gasket Pack
The first item under consideration is described as a Tee Head Bolt with Hex Nut (Part No. TB). The Tee Head Bolt is a partially threaded ¾ x 3 ½ inch (19 mm diameter x 89 inches long) fastener made of low-alloy Corten weathering steel. The Heavy Hex Nut is designed to pair with the Tee Head Bolt and is made of the same low-alloy Corten weathering steel. You state that the Tee Head Bolt and Heavy Hex Nut are both produced from wire rod sourced from Vietnam and China and shipped to Malaysia. In Malaysia, the bolt is cold-forged to the tee-head configuration, threaded and tested. The nut is…
N318659 · 2021-04-28 — The tariff classification of threaded expansion anchors from China
Inc. The first item under consideration is an expansion anchor described as “Wedge-All® wedge anchor”. The wedge anchor provides an anchoring, fastening, and strengthening point in solid concrete and masonry. The Wedge-All® wedge anchor will be imported with a completely assembled threaded bolt, flat washer, and nut. The anchor features a chamfered end and a one-piece, wrap-around clip for uniform holding. The anchor is available in a wide range of diameters and lengths, but you state that all are greater than 6 mm in diameter. The anchor is available in either carbon steel or stainless…
N093625 · 2010-02-28 — The tariff classification of various parts from Taiwan and China
In your undated letter, received in this office on February 4, 2010, you requested a tariff classification ruling. The merchandise consists of five parts designed for use in various types of vehicles. Item number 10256 is an orange plastic 3-legged web clip made in Taiwan. The clip measures approximately 3 inches in length by .75 inch in width. It is temporarily placed on the webbing of a safety seat belt to stop the webbing from retracting until the seat belt is installed in a motor vehicle. After use, the clip will be removed and discarded. Item number 71800004-053 is a tie down strap made…
N090525 · 2010-01-19 — The tariff classification of Gate Hinge Bolts and a Gate Hinge Lag from China.
The samples you have submitted are being returned as you requested. You list and describe the three following part numbers in your submission. RMP0007: 5/8 – 11 x 2 Gate Hinge Bolt RMP0006: ¾ - 12 x 2 Gate Hinge Bolt RMP0025: 5/8 x 6 Gate Hinge Lag Bolt These parts are L-shaped steel components with zinc plating. The long leg is almost fully threaded. The short leg (pintle) ends in a flange. The Gate Hinge Lag contains spaced threading and a gimlet point. The other two items have a blunt point and threading to accommodate a nut. These Gate Hinge Bolts and the Gate Hinge Lag are used to…
N035300 · 2008-08-17 — The tariff classification of steel fasteners from China and Taiwan.
You refer to part numbers RP0824 and RP9602 as T-bolts made of medium carbon steel with zinc platting. Part RP0824 is the larger of the two. Part numbers RP9654 and RP9649 are referred to as spade bolts. Part RP9654 is made of low carbon steel with zinc plating. Part RP9649 is made of stainless steel and is the smaller of the two. The T-bolts and spade bolts are over 12mm in diameter. You state that they are used to tighten steel straps which hold truck fuel tanks in place. The smaller T-bolt can also be used in muffler band straps to secure mufflers to the truck frame and cab assembly. The…
Not sure this code fits your product? HaiLang AI determines the US HTS code from a description in about a minute.
Classify a product