Containing by weight 0.25 percent or more but less than 0.6 percent of carbon: — With a diameter or cross section exceeding 228 mm
Part of: 72155000 — Other, not further worked than cold-formed or cold-finished
966169 · 2003-04-08 — Steel Bars with Chamfered Ends for use as Precision Linear Shafts;
We have considered this submission as a request for reconsideration of New York Ruling letter (NY) I85075, dated September 19, 2002. Your letter was forwarded to this office for reply. A sample was provided for our examination. After review of NY I85075, Customs and Border Protection (Customs) has determined that the classification of the chamfered precision linear shafts under subheadings 7215.50.00, 7222.20.00, 7228.50.50, HTSUS, is correct. FACTS: In NY I85075, in response to your classification request, certain nonalloy steel bars of circular cross section were classified under subheading…
I85075 · 2002-09-18 — The tariff classification of steel bars from Germany.
Descriptive literature was submitted with your ruling request. The products to be imported are solid steel bars of circular cross section. You state that the bars may be nonalloy, alloy or stainless steel. Prior to importation, these bars are ground to specific tolerances and are surface hardened through heat treatment. The bars will be imported in material lengths or in cut lengths. The cut-to-length bars may be chamfered on the ends. Although some of the bars may be drilled or drilled and tapped with holes, this ruling will address only those bars that have not been drilled or tapped. These…
g87398 · 2001-03-18 — The tariff classification of steel bars from various European countries.
The products to be imported are carbon steel hot–rolled rectangular flat bars, hot-rolled square bars, cold drawn square bars and cold drawn round bars. The hot-rolled rectangular flat bars come in a wide range of sizes, e.g. 3 mm x 10 mm; 3 mm x 150 mm; 10 mm x 60 mm; 20 mm x 80 mm; 40 mm x 60 mm; 40 mm x 250 mm. The hot-rolled square bars range in size from 5 mm to 150 mm. The cold drawn square and round bars will also be imported in various sizes. Flat-rolled products are defined in Chapter 72 Note 1. (k) as “Rolled products of solid rectangular (other than square) cross section…in the…
g86568 · 2001-02-01 — The tariff classification of steel channels, beams and flats from various European countries.
The products to be imported are structural carbon steel channels, beams and flats (bars). The channels are hot-rolled and range in size from 51 mm x 38 mm (2” x 1 ½”) to 432 mm x 102 mm (17” x 4”). The hot-rolled beams range in size from 91 mm x 100 mm (3.58” x 3.94”) to 290 mm x 268 mm (11.42” x 10.55”). The cold drawn rectangular flats range in size from 8 mm x 2 mm (0.315” x 0.08”) to 200 mm x 25 mm (7.87” x 0.98”). The applicable subheading for the hot-rolled channels measuring less than 80 mm in height will be 7216.10.00, Harmonized Tariff Schedule of the United States (HTS), which…
963307 · 2000-07-10 — NY E86915 and NY E86936 Revoked; Carbon Steel Lug Base
In NY E86915 and NY E86936, which the Director of Customs National Commodity Specialist Division, New York, issued to you on September 30, 1999, two models of a carbon steel lug base were held to be classifiable in subheading 7211.23.20, Harmonized Tariff Schedule of the United States (HTSUS), as flat-rolled products of iron or nonalloy steel. Pursuant to section 625(c), Tariff Act of 1930 (19 U.S.C. 1625(c)), as amended by section 623 of Title VI (Customs Modernization) of the North American Free Trade Agreement Implementation Act, Pub. L. 103-182, 107 Stat. 2057, 2186 (1993), notice of the…
Not sure this code fits your product? HaiLang AI determines the US HTS code from a description in about a minute.
Classify a product