7215 50 00 90

Code

7215 50 00 90

Type

10-digit tariff line

Duty rate

Free (set at subheading 72155000)

Unit

kg

Classification rulings (U.S. Customs, CROSS)

• N335820 · 2023-10-17 — The tariff classification of continuous cast ductile iron bars from China

  The products under consideration are continuous cast ductile iron bars that will be used as glands and pistons in hydraulic and pneumatic cylinders. You indicate that these cold-finished (i.e., turned or peeled) round bars are made to ASTM A536, Grade 65-45-12 and contain between 3 – 4% carbon. The subject bars are imported in various diameters ranging from 0.5” (12.7 mm) to 24” (609.6 mm) and lengths ranging between 6 and 20 ft. The applicable subheading for the cast ductile iron round bars will be 7215.50.0090, Harmonized Tariff Schedule of the United States (HTSUS), which provides for…

• M86791 · 2006-10-05 — The tariff classification of steel shafts from Japan.

  The product to be imported is described as cold drawn centerless ground rod and bar stock. Cut to length, with diameters ranging from ¼” to 2”, these steel shafts are available in four different chemistries. The stainless product is the equivalent of AISI 440C, the alloy product, also referred to as SUJ2, is the same as AISI 52100 and the carbon products meet the specifications for either AISI 1045 or 1060. Each of these is also available with a chrome plating. All of these products will ultimately be used as guide shafts in hydraulic and pneumatic cylinders in linear machines. The applicable…

• R02292 · 2005-08-09 — The tariff classification of steel bar from Japan.

  The products to be imported are cold drawn/rolled steel bars measuring 7.8 mm in thickness, 31 mm in width and 1,850 mm in length. This particular steel will have a carbon content of 1.00-1.10 percent and a chromium content of less than or equal to 0.30 percent. The applicable subheading for the bars with a chromium content of less 0.30 percent will be 7215.50.0090, Harmonized Tariff Schedule of the United States (HTS), which provides for other bars and rods of iron or nonalloy steel, other, not further worked than cold-formed or cold-finished, containing by weight more than 0.6 percent of…

• 966169 · 2003-04-08 — Steel Bars with Chamfered Ends for use as Precision Linear Shafts;

  We have considered this submission as a request for reconsideration of New York Ruling letter (NY) I85075, dated September 19, 2002. Your letter was forwarded to this office for reply. A sample was provided for our examination. After review of NY I85075, Customs and Border Protection (Customs) has determined that the classification of the chamfered precision linear shafts under subheadings 7215.50.00, 7222.20.00, 7228.50.50, HTSUS, is correct. FACTS: In NY I85075, in response to your classification request, certain nonalloy steel bars of circular cross section were classified under subheading…

• I85075 · 2002-09-18 — The tariff classification of steel bars from Germany.

  Descriptive literature was submitted with your ruling request. The products to be imported are solid steel bars of circular cross section. You state that the bars may be nonalloy, alloy or stainless steel. Prior to importation, these bars are ground to specific tolerances and are surface hardened through heat treatment. The bars will be imported in material lengths or in cut lengths. The cut-to-length bars may be chamfered on the ends. Although some of the bars may be drilled or drilled and tapped with holes, this ruling will address only those bars that have not been drilled or tapped. These…

• 7215 50 00 16 — Containing by weight less than 0.25 percent of carbon: — With a diameter or cross section measuring less than 76 mm
• 7215 50 00 18 — Containing by weight less than 0.25 percent of carbon: — With a diameter or cross section measuring 76 mm or more but not exceeding 228 mm
• 7215 50 00 20 — Containing by weight less than 0.25 percent of carbon: — With a diameter or cross section exceeding 228 mm
• 7215 50 00 61 — Containing by weight 0.25 percent or more but less than 0.6 percent of carbon: — With a diameter or cross section measuring less than 76 mm
• 7215 50 00 63 — Containing by weight 0.25 percent or more but less than 0.6 percent of carbon: — With a diameter or cross section measuring 76 mm or more but not exceeding 228…
• 7215 50 00 65 — Containing by weight 0.25 percent or more but less than 0.6 percent of carbon: — With a diameter or cross section exceeding 228 mm

• 72155 — ТН ВЭД ЕАЭС: без дальнейшей обработки, кроме холодной деформации или отделки в холодном состоянии, прочие
• 721550 — EU CN/TARIC: Other, not further worked than cold-formed or cold-finished

Not sure this code fits your product? HaiLang AI determines the US HTS code from a description in about a minute.