7216 61 00 00

Code

7216 61 00 00

Type

10-digit tariff line

Duty rate

Free

Unit

kg

Classification rulings (U.S. Customs, CROSS)

• N353262 · 2025-09-10 — The tariff classification, country of origin, marking, and eligibility for preferential tariff treatment under the Dominican Republic-Central America-United States Free Trade Agreement (DR-CAFTA)

  The products to be imported are ALUZINC nonalloy steel planks for use in fence construction. The planks are coated in Aluminum-Zinc (AZ) and a layer of Regular Modified Polyester (RMP) for corrosion resistance. Each plank measures 70 inches tall by 6.5 inches wide. In your request, you suggest that the steel planks are properly classified under subheading 7308.90.9590, Harmonized Tariff Schedule of the United States (HTSUS), which provides for Structures (excluding prefabricated buildings of heading 9406) and parts of structures (for example, bridges and bridge sections, lock gates, towers,…

• N342445 · 2024-09-12 — The tariff classification of nonalloy steel angles from Mexico

  The products under consideration are identified as roof bows. According to your submission, the roof bows are used to support the aluminum roof of trailers or truck bodies, maintain the structural alignment of the trailer by connecting the side walls, and keep a consistent distance throughout the trailer. These U-shaped angles are produced from master coils of hot-dipped galvanized, high-strength nonalloy steel and conform to ASTM A653. The coils are slit, roll formed (cold-formed) into the roof bow shape, and then cut to the desired length. Some of the angles may also be drilled with holes…

• N319012 · 2021-05-05 — The tariff classification of steel flashing materials from China.

  Representative photos were submitted with your request. The merchandise in question is 26 gauge (.46 mm) valley roll flashing material used in roofing applications. Comprised of nonalloy steel with a 55% aluminum-zinc alloy (Galvalume) coating, these products are imported in two different configurations. Product 1, imported in coil form, will measure 16” (406.4 mm) in width and 50’ (15240 mm) in length. The tail end of this sheeting is bent to facilitate decoiling. You indicate that these coils will ultimately be cut to length and formed into flashing. Product 2 is a profile shape measuring…

• N303868 · 2019-04-26 — The tariff classification of steel strut channels from China

  A representative sample of the slotted U-shaped channel with inturned edges was submitted with your request and will be returned to you under separate cover. The products under consideration are various 2.5 mm thick nonalloy steel strut channels imported in lengths of 10 or 20 feet. The first channel is U-shaped with inturned edges and has slots uniformly punched along its entire length. Measuring 1 5/8 x 1 5/8, these strut channels are manufactured from mill pre-galvanized sheets. You state that they will either be punched and then roll formed to shape or roll formed to shape and then…

• N294964 · 2018-04-04 — The tariff classification of pallet tracks from China

  The products are described as steel pallet tracks cold-rolled from flat-rolled black steel. After cold-rolling into a modified U shape, that has a squared off recessed middle section bordered by two parallel side strips along its length, the tracks will be cut, chamfered on two corners and drilled with five holes. The imported product is shown in a submitted photo. The submitted mill test certificate shows the chemistry of the steel to be nonalloy. After importation into the U.S., the part described as pallet tracks will be used as a component of about 20 pieces that get welded together to…

• 72161000 — U, I or H sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of less than 80 mm
• 7216 21 00 00 — L or T sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of less than 80 mm: — L sections
• 7216 22 00 00 — L or T sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of less than 80 mm: — T sections
• 7216 31 00 00 — U, I or H sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of 80 mm or more: — U sections
• 7216 32 00 00 — U, I or H sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of 80 mm or more: — I sections (standard beams)
• 72163300 — U, I or H sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of 80 mm or more: — H sections
• 72164000 — L or T sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of 80 mm or more
• 7216 50 00 00 — Other angles, shapes and sections, not further worked than hot-rolled, hot-drawn or extruded
• 7216 69 00 00 — Angles, shapes and sections, not further worked than cold-formed or cold-finished: — Other
• 72169100 — Other: — Cold-formed or cold-finished from flat-rolled products
• 72169900 — Other: — Other

• 721661 — ТН ВЭД ЕАЭС: полученные из плоского проката
• 721661 — EU CN/TARIC: Angles, shapes and sections, not further worked than cold-formed or cold-finished — Obtained from flat-rolled products

Not sure this code fits your product? HaiLang AI determines the US HTS code from a description in about a minute.