Other: — With a diameter or cross section exceeding 228 mm
Part of: 72285050 — Other
N326109 · 2022-06-06 — The tariff classification of alloy steel bars from China, Ukraine or Slovenia
The products under consideration are precision ground alloy steel flat bars. Available in Grades A2, S7 and 01 tool steel and Grade 4140 alloy steel, these cut-to-length bars will ultimately be used in the manufacture of tools, dies and molds. According to your submission, the tool steel bars will measure 2 inches (50.8 mm) in thickness whereas the alloy steel bars will have a thickness ranging from 0.0625 inch (1.58 mm) up to and including 2 inches (50.8 mm). You indicate that these bars will be imported in widths ranging from 0.50 inch to 12 inches (12.7 mm to 304.8 mm). Flat-rolled…
966169 · 2003-04-08 — Steel Bars with Chamfered Ends for use as Precision Linear Shafts;
We have considered this submission as a request for reconsideration of New York Ruling letter (NY) I85075, dated September 19, 2002. Your letter was forwarded to this office for reply. A sample was provided for our examination. After review of NY I85075, Customs and Border Protection (Customs) has determined that the classification of the chamfered precision linear shafts under subheadings 7215.50.00, 7222.20.00, 7228.50.50, HTSUS, is correct. FACTS: In NY I85075, in response to your classification request, certain nonalloy steel bars of circular cross section were classified under subheading…
I85075 · 2002-09-18 — The tariff classification of steel bars from Germany.
Descriptive literature was submitted with your ruling request. The products to be imported are solid steel bars of circular cross section. You state that the bars may be nonalloy, alloy or stainless steel. Prior to importation, these bars are ground to specific tolerances and are surface hardened through heat treatment. The bars will be imported in material lengths or in cut lengths. The cut-to-length bars may be chamfered on the ends. Although some of the bars may be drilled or drilled and tapped with holes, this ruling will address only those bars that have not been drilled or tapped. These…
E83371 · 1999-07-20 — The tariff classification of gear drive systems from South Africa, Hong Kong, Taiwan and Korea
The merchandise is a small DC electric gear motor used to power an electric wheel chair. The complete item includes the motor, gearing and a transaxle. The motors for the gear systems range in power from 300 Watts to 1000 Watts. You also intend to import certain parts for this item, including aluminum die castings, a steel bar, the electromechanical manual release brakes and the separate electric motor. The applicable subheading for both the separate electric motors and the gear drive systems not exceeding 735 Watts in output will be 8501.31.4000, Harmonized Tariff Schedule of the United…
E83514 · 1999-07-13 — The tariff classification of stainless and alloy steel plate from Germany, Japan and Austria.
, you requested a tariff classification ruling. The products to be imported are described as stainless steel mold plate material and NAK 55 manifold material. Stainless steel mold plate material DIN 1.2316 and DIN 1.2085 (1.2316 FM) meet the definition of stainless steel in Chapter 72 Note 1.(e). NAK 55 manifold material meets the definition of other alloy steel in Chapter 72 Note 1.(f). The DIN 1.2316 and DIN 1.2085 stainless plates that range from 37 mm to 127 mm in thickness and the NAK 55 alloy plates that range from 35 mm to 95 mm in thickness are hot-rolled either from ingots or from…
Not sure this code fits your product? HaiLang AI determines the US HTS code from a description in about a minute.
Classify a product